CHANGING THE ANCHOR CORNER


     The AC command positions the starting point of any fill
     pattern. By using this command you ensure that the
     selected fill pattern is positioned as expected within
     the figure.  For more information see the PCL 5 Printer
     Language Technical Reference Manual.


     LEGEND: Ec = [Ctrl] [P] [Esc] in DOS EDIT.


     EcE                           Resets the printer.

     Ec%0B                         Enters HP-GL/2 mode.

     IN;                           Initializes HP-GL/2 mode.

     SP1;                          Selects pen number 1,
                                   (black). Even though
                                   there is no physical pen,
                                   the SP command must be
                                   used to enable printing.

     PA3000,3000;                  Specifies absolute
                                   plotting and moves to
                                   location (3000,3000).

     FT3,400,45;RR1000,1000;
     ER1000,1000;                  Specifies a fill type of
                                   number 3 (parallel
                                   lines), with each line
                                   400 plotter units (plu)
                                   apart and set at a 45
                                   degree angle. RR fills a
                                   rectangle using the
                                   current pen location as
                                   the lower left corner,
                                   and a point 1000 plu to
                                   the right and 1000 plu up
                                   as the upper right
                                   corner. The ER edges the
                                   same rectangle just
                                   filled.


     PR1000,0;FT4,400,45;RR1000,
     1000;ER1000,1000;             Moves 1000 plu to the
                                   right, andselects fill
                                   type 4 (cross-hatch);
                                   then draws a rectangle
                                   the same size as the
                                   first one, and fills it
                                   with the cross-hatch
                                   pattern just specified,
                                   then edges it with the ER
                                   command.

     PR1000,0;FT3,400,45;
     RR1000,1000;ER1000,1000;      Moves to the right
                                   another 1000 plu, and
                                   creates another rectangle
                                   of the same size, then
                                   fills this one with the
                                   number 3 fill pattern
                                   again. Then edges the
                                   rectangle just specified.

     PA3000,1500;AC3000,1500;
     RR1000,1000;ER1000,1000;      Moves the pen to absolute
                                   position (3000,1500), and
                                   moves the anchor corner
                                   to location (3000,1500).
                                   Fills a rectangle with
                                   the fill pattern selected
                                   (number 3 from the
                                   command above), and edges
                                   it.

     PA4000,1500;AC4000,1500;
     FT4,400,45;RR1000,1000,
     ER1000,1000;                  Moves to location
                                   (4000,1500) andspecifies
                                   the location as the
                                   anchor corner. Selects
                                   fill type number 4 again,
                                   then fills, and edges a
                                   rectangle.


     PA5000,1500;AC5000,1500;
     FT3,400,45;RR1000,1000;
     ER1000,1000;                  Moves to absolute
                                   location (5000,1500)and
                                   specifies that location
                                   as the anchor corner,
                                   then selects fill type 3
                                   again, and fills and
                                   edges another rectangle.

     Ec%0A                         Enters PCL mode.

     EcE                           Sends a reset to end the
                                   job and eject the page.


          NOTE:  Due to space limitations these
                 lines of code appear on more
                 than one line. When entered into
                 the DOS editor they should
                 appear on one line.


            Copyright  Hewlett-Packard Co. 1993
   The information contained herein is subject to change
                      without notice.
   Hewlett-Packard shall not be liable for incidental or
  consequential damages in connection with the use of this
                         material.